JET 708580 Use and Care Manual download pdf (Page 4)

Warning

• KEEP GUARDS IN PLACE and in order.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form the habit of checking to see that keys and adjusting

wrenches are removed from the tool before turning it on.

• KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.

• DO NOT USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose

them to rain. Keep work area well lighted.

• KEEP CHILDREN AWAY. All visitors should be kept safe distance from the work area.

• MAKE THE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.

• DON’T FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.

• USE THE RIGHT TOOL. Don’t force a tool or attachment to do a job for which it was not designed.

• USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord

will cause a drop in the line voltage resulting in loss of power and overheating. For runs up to 25 feet, use a 16

AWG or larger gauge cord. For runs up to 50 feet, use a 16 AWG or larger cord. For runs up to 100 feet,

use a 14 AWG or larger cord. If in doubt, use the next heavier gauge. The smaller the gauge number, the

heavier the cord.

• WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry

which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to

contain long hair.

• ALWAYS USE SAFETY GLASSES. Also use face or dust masks if the cutting operation is dusty. Everyday

eyeglasses only have impact resistant lenses, they are NOT safety glasses.

• SECURE WORK. Use clamps or a vise to hold the work when it’s practical. It’s safer than using your hand and it

frees both hands to operate the tool.

• DON’T OVERREACH. Keep proper footing and balance at all times.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

• DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits cutters, and the like.

• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before

plugging in the machine.

• USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use

of improper accessories may cause a risk of injury.

• NEVER STAND ON A TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally

contacted.

• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly and perform its intended function. Check for alignment

of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect

its operation. A guard or other part that is damaged should be properly repaired or replaced.

• DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter

only.

• NEVER LEAVE THE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Don’t leave the tool until it

comes to a complete stop.

• WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities

contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

• Lead from lead based paint.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these

chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks

that are specifically designed to filter out microscopic particles.

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

JET 708580 Use and Care Manual Page 4

Comments to this Manuals

Related products and manuals for Power tools JET 708580