JET 708677PK Use and Care Manual

Operating Instructions and Parts Manual 10-inch XACTA Saw Deluxe JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-70867

10 Extension Wing Referring to Figures 4 and 5:  Hardware: (6) 7/16”x1-1/2” Hex Cap Bolts, (6) 7/16” Lock Washers, (6) 7/16” Flat Washers & (2

11 Riving Knife and Guard Installation Description Referring to Figure 7: The complete riving knife and guard assembly is shown in A. Before installi

12 Mounting Rails & Extension Table With the extension wings properly aligned, the rail and fence assembly can now be mounted to the saw. Refer t

13 Adjustments Handwheel Adjustments Referring to Figure 10: The front handwheel (B) controls the raising and lowering of the blade (blade height).

14 Riving Knife Adjustment Lateral alignment The saw blade and riving knife must be in line as close as possible with each other (lateral alignment)

15 Blade Alignment  Tools: 8mm hex wrench, combination square, marker Blade alignment with the table is adjusted at the factory. After a period of

16 5. If blade is not at 90 degrees, open the motor cover door, loosen lock nut (A, Fig. 19) and turn adjusting stop screw (B, Fig. 19) on the front

17 Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Clean

18 Troubleshooting Trouble Possible Cause Solution Saw stops or will not start Overload tripped Saw unplugged from wall or motor Fuse blown or circu

19 Optional Accessories Stock No Description 708097 Dado Insert 708118 Universal Mobile Base 708295 Tenoning Jig 708401 Downdraft Table for XACTA D

2Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact

20 Table & Cabinet Parts List Index No. Part No. Description Size Qty 1 ... JTAS10-1 ...Lock Knob ...

21 Table and Cabinet Parts List Index No. Part No. Description Size Qty 47 ... TS-0210011 ...Socket Head Cap Screw ...

22 Table & Cabinet Exploded View 423839414040(474)20 (4)49(4544431575643)(3 2 119(6)20 (6))186(112))(4281093(8))(12613146113A356228(4)505955(2)5

23 Trunnion & Motor Parts List Index No. Part No. Description Size Qty 101 ... JTAS10L-101 ...Arbor Nut ...

24 Trunnion & Motor Parts List Index No. Part No. Description Size Qty 149 ... TS-0208041 ...Socket Head Cap Screw ...

25 Trunnion & Motor Assembly Drawing

26 Blade Guard Parts and Assembly Index No. Part No. Description Size Qty 1 ... JTAS10L-301 ...Riving Knife ...

27 Wiring Diagrams for XACTA Deluxe Table Saws 3HP/5HP, 230V, 1Phase

28 5HP, 230V, 3 Phase

3Table of Contents Warranty and Service ...

4 Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings poste

5 19. Keep visitors a safe distance from the work area. Keep children away. 20. Make your workshop child proof with padlocks, master switches or by r

6Introduction The JET XACTA® Saw Deluxe table saw you have purchased is a high quality machine tool that will give you years of superior service. You

7 Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury. Shipp

8 Contents of the Shipping ContainerMain Saw Container 1 Table Saw (A) 1 Switch (B) 1 Table Insert (C) 1 Owner's Manual (D) 1 Warrant

9 Assembly Motor Cover Referring to Figures 1 and 2:  Tools: 17mm Wrench, 12mm Wrench 1. Remove shipping bracket (A) securing the motor (C) to tab