JET 707110 Use and Care Manual

Operating Instructions and Parts Manual 10" Sliding Dual Bevel Compound Miter Saw Benchtop Series – Model No. JMS-10SCMS WALTER MEIER (

10Shipping Contents Unpacking 1. Remove the contents from the shipping container. 2. Compare the contents of the shipping container with the list fo

11Releasing the Cutting Head When not in use, lock the cutting head in the down position. Failure to comply can cause serious injury or damage equi

12Table Inserts Always unplug the saw to avoid accidental starting. Failure to comply may cause serious injury!  Remove table insert to remove all

13Installing Blade Important: This machine requires a 10-inch diameter blade. Unplug the miter saw before changing and/or installing the blade. Refer

14Adjustments Before attempting any adjust-ments – To avoid injury from unexpected starting or electrical shock make sure the trigger is released an

159. Test the 90° alignment as follows: Unlock bevel lock handle (A, Fig. 8), and pull out bevel detent pin (E, Fig. 10). Rotate head left or right,

166. Repeat steps 1–4 if necessary until the blade is 45° to the table, then tighten the lock nut (D, Fig. 12) to secure the stop bolt (C, Fig. 12)

17Adjusting Fence Squareness 1. Loosen four fence locking screws (D, Fig. 18).Note: two locking screws to each fence. 2. Lower the cutting arm and l

18Note: The quick-cam miter table lock should lock the table and prevent it from moving. If adjustment is needed, see Quick-cam Miter Table Lock Adju

19service center. • Laser radiation. Avoid direct eye exposure. Always un-plug miter saw from power source before making any adjustments. • Laser

2Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Aut

20Sliding Fence The sliding fence must be extended to the left or right when making bevel cuts. Failure to comply may cause serious injury! Failure

21same time grasp the miter handle (D) and rotate the miter table left or right to the desired angle. 3. Release the positive stop locking lever (C),

22Compound Cuts Referring to Figure 27: Setting the bevel angle 1. Extend the fence by sliding it out to the required location (see Sliding Fence on

23Slide Cutting Wide Boards Observe the following precautions:  Never pull the cutting head assembly and spinning blade toward you during the cut.

24Rough Cutting a Dado 1. Mark lines identifying the width and depth of the desired cut on the workpiece and position on the table so the inside tip

25Bevel/Miter Settings Settings for standard crown molding lying flat on compound miter saw table. Note: The chart below references a compound cut fo

26Crown Molding Chart Compound miter saw miter and bevel angle settings, wall to crown molding angles 52/38º Crown Molding 45/45º Crown Molding

27Maintenance To avoid injury while performing maintenance, always unplug the power cord before working on the saw. Failure to comply may cause seri

28Troubleshooting – Motor Trouble Probable Cause Remedy Brake does not stop blade within 10 seconds. Motor brushes not sealed or lightly sticking.

29Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for bus

3Table of Contents Warranty and Service ...

30Parts List Index No. Part No. Description Size Qty 48 ... TS-1504031 ...Socket Head Cap Screw ...

31Parts List Index No. Part No. Description Size Qty 106 ... ...Slide Bar, Right ...

32Parts List Index No. Part No. Description Size Qty 164 ... JMS10SCMS-164 ...Compression Spring ...

33Assembly Drawing

34Assembly Drawing

35Assembly Drawing

36Wiring Diagram WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-68

4 Warnings 1. Read and understand the entire owners' manual before attempting assembly or operation. 2. Read and understand the warnings poste

5 21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks, master switches or by r

6Compound Miter Saw Safety Specific safety instructions for this compound miter saw: 1. Do not operate the miter saw until it is completely assemble

7Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for the JET Model

8Electrical Power Supply and Motor Specifications The AC motor used in this saw is a universal, nonreversible type (see Motor in the Specifica-tions

9Features