JET 707100 Use and Care Manual

CUSR 174315 Operating Instructions and Parts Manual 10" Compound Miter Saw Benchtop Series – Model No. JMS-10CMS WALTER MEIER (Manu

10Shipping Contents Unpacking 1. Remove the contents from the shipping container. 2. Compare the contents of the shipping container with the list fo

11Assembly Releasing the Cutting Head When not in use, lock the cutting head in the down position. Failure to comply can cause serious injury or da

12Installing the Safety Hold-down Clamp 1. Place the hold-down clamp assembly (A, Fig. 4) in a mounting hole located behind the right or left (shown)

139. Remove the arbor bolt (H), arbor collar (J), and blade (K). Do not remove the inner blade collar. Note: Pay attention to the pieces removed, not

14Adjustments Before attempting any adjust-ments, make sure the trigger is released and remove the power cord from the power source to avoid injury

1545° Left Bevel Positive Stop Adjustment 1. Set the miter angle to 0° (Miter Angle - page 15) and fully extend the sliding fence (Sliding Fence - p

16Adjusting Fence Squareness Referring to Figure 11: 1. Loosen two fence locking screws (C). Note: One locking screw is located on each fence. 2. Lo

17Quick-cam Miter Table Lock Adjustment Referring to Figure 13: 1. Place the quick-cam miter lock (A) in the down position to lock. 2. Loosen the lo

18Operation Before attempting any operation with your miter saw, make sure that you have read and thoroughly understand the warnings contained on pa

19Sliding Fence The sliding fence must be extended to the left or right when making bevel cuts. Failure to comply may cause serious injury! Failure

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

20Bevel Cut The sliding fence must be extended to the left when making bevel cuts. Failure to comply may cause serious injury! Failure to extend the

21 Repetitive Cutting Note: Long workpieces need extension table support. Referring to Figure 20: Loosen the knob (E) then slide the extension wing (

22Cutting Base Molding Base moldings and many other moldings can be cut on a compound miter saw. The setup of the saw depends on molding characterist

23Crown Molding Chart Compound miter saw miter and bevel angle settings, wall to crown molding angles 52/38º Crown Molding 45/45º Crown Molding

24Maintenance To avoid injury while performing maintenance, always unplug the power cord before working on the saw. Failure to comply may cause seri

Troubleshooting – Motor Trouble Probable Cause Remedy Brake does not stop blade within 10 seconds. 1. Motor brushes not sealed or lightly stick

26Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for bus

27Parts List Index No. Part No. Description Size Qty 48 ... TS-1550061 ...Flat Washer...

28Parts List Index No. Part No. Description Size Qty 106 ... JMS10SCMS-54 ...Arbor Bolt ...

29Parts List Index No. Part No. Description Size Qty 167 ... JMS10CMS-167 ...Label: Bevel Lock ...

Table of Contents Warranty and Service...

30Assembly Drawing

31Assembly Drawing (continued)

32Assembly Drawing (continued)

33Wiring Diagram

34Notes

35Notes

40 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.walter

4 Warni ngs 1. Read and understand the entire owners' manual before attempting assembly or operation. 2. Read and understand the warnings pos

5 20. Don't use in dangerous environment. Don't use power tools in damp or wet locations, or expose them to rain. Keep work area well ligh

6 Compound Miter Saw Safety Specific safety instructions for this compound miter saw 1. Do not operate the miter saw until it is completely assemble

7 Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for the JET Model

8 Electrical Power Supply and Motor Specifications The AC motor used in this saw is a universal, nonreversible type (see Motor in the Specifica-tions

9 Features